Finally had a chance to change the valve. by Fred M Earned 109,903 community points in Click'>Kenmore September 1st, 2010 Comment 0 votes Sorry for the delay . LonnieJohnson1 1,292 views 9:39 Sears, Kenmore, Whirlpool & Maytag Refrigerator Repair & diagnostic - Leaking water on floor - Duration: 13:52. Sign in to make your opinion count. weblink
Service has been out 3 times with no solutionThis is a new machine purchased in March 2016. hammydude12345 559,954 views 4:06 Loading more suggestions... My neighbor suggested there might be a kink in the line from the water to the fridge, so this weekend I replaced it with a nylon hose. Normal would be pointing at you or slightly above you. http://www.applianceblog.com/mainforums/threads/8007-Kenmore-Coldspot-Ice-Maker-Stopped-Working
ApplianceVideo.com 47,318 views 8:14 Kenmore ice maker frozen up and not working like it should - Duration: 3:09. Extended vacation ... Check for ice on the outside of the tube and wiggle the tube to see if it's frozen. Kenmore Coldspot 106 Ice Maker Diagram Matt Spencer 138,398 views 17:36 My Refrigerator is Leaking Water Inside the Freezer! - Duration: 1:43.
Thanks again for having this forum. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... by Fred M Earned 109,903 community points in Click'>Kenmore May 3rd, 2011 Comment 0 votes I've been looking for a complete ice maker to replace instead of the module.
If the ice maker doesn't harvest and doesn't fill with the jumper in place then I believe the ice maker is the problem.
Now disconnect power to the refrigerator. Kenmore Coldspot Ice Maker Leaking Water So you needed to cut the old hoses to fit the new fittings. Loading... Lint filter does not fit in the slot and clothes are getting caugh...
The water should flow freely into the bucket. have a peek at these guys Step#1: Open the freezer and view the status led (STATUS LED) 2 BLINKS FOLLOWED BY 1 SEC. by afritz afritz Earned 46,232 community points in Click'>Kenmore August 19th, 2010 Answered in 11 minutes Comment -1 votes Didn't find what you are looking for? Water is flowing fine from outside dispenser. Kenmore Coldspot Ice Maker Not Getting Water
If the ice maker works this time then most likely the emitter board is the problem. okay the ice maker itself has failed, the fingers should be in the position shown here. Ask Your Own Appliance Question Customer: replied4 years ago. check over here There are also some very good images that should help clear up any problem you might have.
What's New? Kenmore Coldspot 106 Ice Maker Removal There was a bit of play, not sure how far that wire needed to go--I went till it wouldn't go in any further. RepairClinic.com 71,313 views 3:02 How to repair most refrigerator ice-makers for less than $20 - Duration: 4:06.
Thanks! I did some searching on-line, and last night we removed the actual ice maker itself (just remove one screw and it pulls out), and there is no ice frozen in there, This is my second set of front load washer and dryers from K... Kenmore Refrigerator Ice Maker Not Making Ice Or it could be something as mundane as a door switch failure.A what?If you had an ice maker in the door, the door switch turns off ice production when the door
ApplianceAdvice 250,404 views 2:49 How Does The Ice Maker On A Refrigerator Work? — Appliance Repair & Troubleshooting Tips - Duration: 3:32. by Manage My Life September 24th, 2011 Answered in 30 minutes Comment Give your feedback by voting on answers 0 votes Thank you for your question. by Manage My Life August 2nd, 2011 Comment 0 votes Hello, can someone post or point me to installation instructions for item W10190935 - Ice maker motor module head? Thank you this content SamuraiRepairman 263,494 views 2:34 Ice maker or water dispenser not working - Refrigerator repair - Kenmore Whirlpool - Duration: 13:14.
See Details Related Pages Kenmore 5M followers Follow Refrigerators 2K followers Follow Not only Santa needs a listSave gift ideas to your "Gift List" catalog Sweeps Personal Shopper Gift Registry Legal Tips & Warnings Be very cautious when working with electrical appliances in wet areas. It appears OK, although at the top where it goes back in there is some white discoloration, which I'm not sure is just what happens when you bend a white plastic Bryan is online now I have a kenmore cold spot model 106.
Kenmore cold spot 106 ice maker issues Started by Ravenar, Jul 07 2012 10:23 am Please log in to reply 9 replies to this topic #1 Ravenar Ravenar 1,000 Post Club! Thank you for your support. Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Compact Refrigerator See Details Related Pages Kenmore 5M followers Follow Appliances 168K followers Follow Refrigerators 2K followers Follow Not only Santa needs a listSave gift ideas to your "Gift List" catalog
You will now see the test terminals, which are marked (see picture). A water inlet valve attaches to a water supply line... Question? If there is anything that can be done to remedy this situation NOW, we will very much appreciate the assistance. see more...November 10, 2016 · Answer · Like0 · Follow0 Show 3
This feature is not available right now. are they supposed to be up or laying flat Expert: Bryan replied4 years ago. Learn more You're viewing YouTube in English (United Kingdom). And a chunk of ice frozen in the water line could have a similar effect.You may have a problem with water pressure, since the ice maker won’t work if water pressure