Your headphones plug into a jack that is on this flex cable as well. Apple iPhone 5 Front Camera and Proximity Sensor Troubleshooting: The Apple iPhone 5 Front Camera and Proximity Sensor is composed of 2 different parts. Tom Brandolini - 03/06/2011 Reply Definitely watch out to have all your connectors above the board. If your new housing does not fit, double check the model number on the back of your original iPhone housing. have a peek here
Try removing, and reinstalling your apps one by one to figure out which one is causing the problem. You should not need to change phone numbers to get a new SIM card. If your new button will click, but your device will not respond, double check that your home button flex cable is lined up correctly. This repair can be done without removing any additional parts on your device.
I just installed it and the ear speaker still doesn't work. Loading... germanperezsalva - 07/18/2013 Reply When I put the new battery in, it was a smidge too far toward the bottom. Add to Want to watch this again later?
Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... A tip: to handle the screws, very small, I used a pair of tweezers for eyebrows wrapped in double sided adhesive tape. Do that with your thumb and the tips of your fingers on the other side. How To Turn On Iphone 3gs Without Power Button So my question is: Which component do i replace?
Are they supposed to snap into place? Iphone 3gs Power Button Not Working Solution Cancel Add your answer Tommy will be eternally grateful. I used an equally small flat-blade screwdriver and gently walked around the battery lifting against the bottom plastic and the edge of the phone being careful NEVER to touch any of https://www.ifixit.com/Answers/View/59251/After+replacing+back,+power+button+won't+work+(even+pushing) It was removed and set aside many steps ago.
You can try restoring your device to factory default settings (after the battery replacement); however, if the main board happens to be bad as well, then Apple will not touch your Iphone 3gs Manual Transcript The interactive transcript could not be loaded. bobbyfrog - 01/22/2010 Reply I successfully completed these steps to dry out a wet phone. Sign in 629 57 Don't like this video?
Start with a backup and restore of your device through iTunes (the steps for this can be found earlier in this blog).
Check to see if your screen's back light is on. Iphone 3g Power Button Repair Remove the battery and see if you can plug straight into a charger to get life. Iphone 3gs Home Button Also, I seem to have lost bass in music, and the volume control buttons work but don't physically click like they should.
jgerth - 11/23/2011 Reply I did all of these steps but now my Iphone is stuck as a black screen with the apple and wont do anything...HELP! navigate here CAUTION: Pull with the suction cup near the round button, AND ALSO have someone else support the other end of the display so that only the end of the display with start looking in that place Was this answer helpful? Wait 60 seconds. Iphone 3 On Off Button Not Working
gareth jones - 05/08/2010 Reply Be careful when trying to pry the battery from the side, as the spudger will break. If all the cables look intact make certain all your cables fit properly. View the answer I have this problem too Subscribed to new answers Is this a good question? http://unmovie.net/iphone-3/iphone-3-power-switch-not-working.html You'll need to get someone equipped to repair circuit boards.
There should be 2 prongs that make a constant connection with your home button flex. Iphone 3g Home Button Not Working AppleiPodParts.com 450,005 views 39:03 Official iPhone 3G / 3GS Screen / Digitizer Repair and Replacement Video - iCracked.com - Duration: 17:03. Be sure to subscribe if you liked the video.
Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered. AppleiPodParts.com 336,591 views 17:24 iPhone Home Button Not Working? Reply Bill September 17, 2014 I replaced my iphone5 screen with a new one that contained all the parts, all I had to do was plug in the 3 Ifixit Iphone 3gs However if I get the phone in lock mode I won't be able to wake it up unless I connect it to the computer/power outlet or use the headsets to activate
Now carefully use the suction cup to 'walk/rock' the screen out with a left-to-right while pulling up motions. I replaced my Apple iPhone 5 Touch Screen Digitizer With LCD Display, now it will not work! Is it the "Do not remove tape"? http://unmovie.net/iphone-3/iphone-top-button-not-working-3gs.html iPhoneRepairMia 90,182 views 3:42 FIX Home Button Hard to Press, Losing Sensitivity Over Time Without Opening case_ l0000gold.mp4 - Duration: 8:16.
If iTunes says your device cannot be reset or restored, then there is damage to the motherboard of your device. This will keep glass shards contained and provide structural integrity when prying and lifting the display. Click Restore. That's what I'll have to do.
You will need to replace your LCD to resolve this problem. screen was not responding, It was doing things on its own.. There is a corresponding clip on the opposite side of the north end the logic board, facing east (a bit east of the #6 ribbon cable). johnhart - 02/10/2010 Reply Slipping the SIM card in first is a helpful suggestion.
Reply Doctor Jeff August 22, 2014 You may have had a cable inside the device that was coming loose, and was able to be reconnected for short periods of time. Is it possible I've damaged the aerial in the process? The home button flex is composed of a single flex cable with 2 copper contacts on the loose side. As of this date (June 2015), only those three guides include a photo of a mock-up of Connector 3 that will provide you with detail that will help you avoid damaging
The issue is that when I opened up my phone the screen and touch screen came up, but there is still a screen covering my entire back housing...is there a way