Home > Iphone 3gs > Iphone 3gs Vibrate Switch Not Working

Iphone 3gs Vibrate Switch Not Working

that way i dont accidentally turn it off or up or whatever . This will allow easier access for disconnecting the remaining cables. Mike M - 02/14/2010 Reply I've done all the steps and phone switches on and works just fine with the one exception that I do have a signal! Sign in to report inappropriate content. http://unmovie.net/iphone-3gs/iphone-3gs-vibrate-not-working.html

OpinionativeReviewer 6,188 views 2:18 iPhone 8 Trailer 2017 - Duration: 3:15. Take your time with this step and make sure the mute rocker feels normal before attaching anything else (phone jack, power button, etc.). Loading... Can replace a broken Silent switch - Duration: 3:08.

Those things get very hot. You can tell where this piece is supposed to go because you will see a small edge, (on the inside of the exterior part of the switch) and a thin grey I have set of new screws here an I need to sort them - I can't find more detailled specifications on the four screws mentioned here.

iPhoneRepairMia 260,848 views 6:45 14 Things You Didn't know You Could do With an iPhone! - Duration: 6:45. My phone was replaced on warranty in February so this must be the case in some newer 3G's. I put too much pressure on it so now I have a cell phone without WiFi or GPS. The strange thing is that on checking the networks I can see T-Mobile, but not 02, so implies something is working.

However you will lose a few things like your outgoing message and a few other things. John - 02/20/2010 Reply You most likely forgot to re-atatch the antenna. Try "parallel and aligned". https://www.ifixit.com/Guide/iPhone+3G+Mute+Button+Replacement/581 and you'll have to pull all the screws back out and figure out what you did wrong (and why you had a naggling suspicion the logic board wasn't placed quite right).

Looking at the picture makes this step brain dead simple, but if you were using another iPhone to read the directions it would be easy to miss. I think i may have fixed it now though. Mathias - 04/21/2012 Reply Since I didn't have a hair dryer (never needed one) I used a 500W construction lamp... Sign in 15 Loading...

This will keep glass shards contained and provide structural integrity when prying and lifting the display.

slessard - 09/06/2011 Reply Be very careful, in some cases the ribbon damages. Thanks. DefCharlie - 05/24/2012 Reply Had to use pliers to slowly pull the battery free by it's tab.

the air came out. http://unmovie.net/iphone-3gs/iphone-3gs-vibrate-motor-not-working.html So because I reassembled too quickly the first time - I got to do all the steps 3 times! iHelpCorner 819,716 views 7:28 How to make any iPhone LOUDER for FREE! It is also a paid tweak but comes with automatic and manual switching functionality.

Loading... One 3.8 mm Phillips #00 screw in the plastic loop near the headphone jack. 5 comments Can somebody say me, if the screw (1.8 mm) on the left side is very Amazingly to me, I was able to slide the flex tail back in to position and it made all the necessary electrical contacts (at least for the time being). http://unmovie.net/iphone-3gs/iphone-3gs-vibrate-not-working-fix.html Is it possible I've damaged the aerial in the process?

Instead, I used a folding bone (something I've had for years that's used for making perfect folds in heavy printmaking paper) however, I was still bending the battery far more than I finally had to give up. Tom Brandolini - 05/17/2014 Months ago I wrote and placed an edit into step 10 which read something like this: " Be very certain that the #6 connector half on the

n1viperx 42,966 views 21:07 iPhone 3G & 3GS Headphone Jack and Buttons Cable Replacement Guide - www.AppleiPodParts.com - Duration: 12:10.

The strange thing is that on checking the networks I can see T-Mobile, but not 02, so implies something is working. Loading... The 'trick' is that once you have inserted the cable into the body of the connector, quickly slide the bar back toward the body as this will lock the cable into Do that with your thumb and the tips of your fingers on the other side.

After stripping it all down I then put it all back together but now my lock button doesnt work. Terms and Conditions of using our services are at www.thecomputerroomnottingham.co.uk/terms-and-conditions. orangey456 234,945 views 8:26 Iphone 4 not vibrating - Duration: 1:52. this contact form Dieter Groll - 05/23/2014 #6 would not reattach.

The end result of any such mishap is commonly either a broken screen, broken mute button or malfunctioning volume buttons and headphone jack and in worst of the cases, all at It also shuts down with use. This feature is not available right now. Don't fear, if you have a soldering iron you can melt these away and gently pull off the old switch and ribbon cable assembly. 2) Installing the new switch/ribbon cable assembly

Fine point tweezers would help here, to take it out and to put back in place during re-assembly. Any suggestions?? This was very effective as my screen was pretty jammed into the case so need extra leverage using the metal ring on the screen sucker Alf - 05/17/2014 Reply I had After this damage the proximity sensor won't work anymore.

The logic board would not fit back perfectly because of the bloated battery. There is a small golden grounding tab on logic board adjacent to the 'do not remove sticker'. Quote from Vishal Vaidya: Is there a way of replacing the connector? there is a place in i tunes while you are still connected you can re-set the phone to the default settings and that should do it.

Uploaded on Oct 15, 2011I tell you how you can bypass the Ringer/Silent switch for your iphone 3GS or iPhone 4 if your switch doesn't work to stay silent.You do have Andy iggy1967 *at* hotmail.com iggypop - 04/23/2010 Reply I'm having a hard time reversing this process. But I am sure not many of are that lucky, so what can we do? I can turn the phone on by plugging it in and then out again only.

I used an equally small flat-blade screwdriver and gently walked around the battery lifting against the bottom plastic and the edge of the phone being careful NEVER to touch any of This may require a magnifying glass or jewelers' loupe. 11 comments Those "6" and "7" antenna connectors are quite fragile. for instance how the button itself should be placed and what screw should be used, by mistake I had some screws mixed and now I don't recognize which one should be atlemar - 08/24/2013 Reply Add a comment Add Comment 1024 Step 14 Edit Use a spudger to gently pry up the end of the logic board closest to the dock connector.