Home > Iphone 3gs > Iphone 3gs Volume Button Not Working

Iphone 3gs Volume Button Not Working

My phone was replaced on warranty in February so this must be the case in some newer 3G's. Acción en curso... the iPod plays fine through the speakers, but sounds faraway in headphones -almost as if mono through both cans. I can turn the phone on by plugging it in and then out again only. Check This Out

Check if Volume Changes With and Without Headphones In some cases, faulty connections between the phone and the headphones can cause changes in volume. There is a small golden grounding tab on logic board adjacent to the 'do not remove sticker'. I will give this a try. 10/30/2012 by Tetsuro Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? If I follow this guide, will I be able to pull my phone apart, change the covers and put it back together? https://discussions.apple.com/thread/3298461?tstart=0

What is it? Give the author +30 points! Still hope wasn't damaged, we'll see in a few minutes :) iluxan - 08/17/2011 Reply check also that the golden cicuit is opened when the sim card tray is inserted.

Cambiar a otro idioma: Català | Euskara | Galego | Ver todo Learn more You're viewing YouTube in Spanish (Spain). Alessandro AlexPi - 11/13/2009 Reply Well, I took the chance and the LCD broke on this step. Cancel kunjal patel Rep: 1 Posted: 06/26/2012 Options Permalink History YOU MIGHT NEED TO LONG PRESS THE CURRENT ONE THAT'S NOT WORKING. Roger Soucy - 06/02/2011 Reply I had some trouble getting the mute switch/rocker to function properly, as a couple others have mentioned.

djjdohio - 02/09/2015 Reply Add a comment Add Comment 1024 Step 13 Edit Use a spudger to gently pry the camera up and out of its housing in the rear case. Fine point tweezers would help here, to take it out and to put back in place during re-assembly. Lester Nidoy 40.490 visualizaciones 0:48 Cargando más sugerencias... https://www.ifixit.com/Answers/View/35696/Why+is+my+volume+up+button+switch+not+working Christian Schiefer - 07/24/2010 Reply Always test the button after replacement, if its not moving freely, loosen both sides or take one screw out, and refit, its like the mute switch,

What is the function of this screw? Cola de reproducción Cola __count__/__total__ How to fix iphone 3g volume buttons frankie teixeira SuscribirseSuscritoCancelar1111 Cargando... Cargando... Añadir a ¿Quieres volver a verlo más tarde?

iRepairFast 82.351 visualizaciones 1:17:13 iPhone 4 Audio problems.MP4 - Duración: 4:17.

Inicia sesión para añadir este vídeo a la lista Ver más tarde. You can use a hair dryer or heat gun on its lowest setting to heat the back of the case. The good side is that iFixit's screwdriver is magnetized, a bonus when working with such small parts.

All rights reserved. http://unmovie.net/iphone-3gs/iphone-3gs-vibrate-not-working-fix.html jonatgree - 01/22/2014 Reply I replaced the battery and it works great...battery wise...however my home button and power button do not work. If you like please subscribe and comment. iPhoneRepairMia 260.848 visualizaciones 6:45 iPod Touch Volume Control Hack - Duración: 2:32.

lazygorilla - 02/03/2010 Reply I did not need to remove the battery. Esta función no está disponible en este momento. What could of happened? this contact form Quote from Vishal Vaidya: Is there a way of replacing the connector?

Cargando... You could replace it. Inicia sesión para que tengamos en cuenta tu opinión.

Then make sure to set the top section of the logic board (where the SIM tray is) in place before settling the rest of the board in place.

My 3GS is now effectively an iPod, but with a new battery. germanperezsalva - 07/18/2013 Reply When I put the new battery in, it was a smidge too far toward the bottom. The most obvious clip is next to the camera, facing south (if the camera is in the NE corner). In the picture above, it simply jumped out for no reason, while I had to use a tweezer to make it out...

oh also the vibrate button won't work any ideas there? Currently my iPhone has become an iPod! Maybe it adds Value to the explanation to say that the piece that needs to be flipped up is located on the opposite side of where the ribbon cable exits the navigate here Switch to another language: Catalan | Basque | Galician | View all Cerrar Sí, quiero conservarla.

Use a spudger to flip up the white plastic tab holding the ribbon cable "3" in place. and thats all?