If that doesn't work you may have an issue with the connector in the phone itself. In any case, docking and undocking it fix my problem.It may not work for everyone, but it did for me.Hope it works for you. Remove the top logic board shield There are 5 screws holding the logic board shield in place. The oils from your fingers have the potential to cause wireless interference issues. have a peek here
Word of warning however, the speakers are a PAIN to put back in without removing the logic board. May 18, 2012 1:13 AM Helpful (0) Reply options Link to this post by iOSgaga, iOSgaga Jan 5, 2013 7:42 PM in response to seanbperiod Level 1 (0 points) Jan 5, Just use a bit of heat ( not a lot! ) to soften up the glue and it'll come away with the plastic pull tab. To remove the back simply slide the back upwards and lift it off gently.
Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Going into the Music app shows that it thinks it's outputting the music to the dock connector. share|improve this answer edited May 12 '15 at 10:51 Jens Erat 1,54861528 answered May 12 '15 at 9:21 nostoc_retgame 1 add a comment| up vote -1 down vote I have an
justinstayton - 01/06/2013 Just got it, first try! iFixit Video 1,379,914 views 7:02 How to get your stuck or unresponsive iPhone home button working again - Duration: 2:15. Almost all newer devices will have security screws. Iphone 4 Charging Port Repair Cost Loading...
You can either follow these steps in reverse order or watch our reassembly video above starting at about 3:20. Iphone 4 Dock Connector All the parts were purchased on this website so I would think that they would be high quality. Podcasts Contact iMore About iMore Android Central Connectedly CrackBerry iMore Windows Central Tesla Central VR Heads MrMobile DIY How to replace a broken iPhone 5 screen in under 10 minutes DIY I plugged it in and immediately the screen displayed a battery with a thin red line (illustrating no charge).
dfrisch86 - 01/22/2014 Reply Installed new battery without a problem. Iphone 4 Dock Connector Replacement It should come up easily so pry up gently.You'll notice that it is wrapped around a metal clip. it's a hardware issue most likely. I need my phone asap since this is my work phone.
Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. Use either your #00 screwdriver or the five point depending on whether or not your iPhone 4 has security screws in the dock connector. Iphone 4 Charging Port Replacement Once you unclip the seven cables, you can lift the rear-facing camera directly out of the iPhone. Iphone 4 Dock Connector No Sound Sign in to add this to Watch Later Add to Loading playlists...
I am thinking it's a bad button. 06/22/2012 by JBA Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? navigate here lens42 - 10/12/2011 I use a plastic egg tray, I drop all the screws and small parts (like the camera) for each step into the same egg indentation. Depending on what you're replacing, the video teardown may not cover everything. Remove the back First remove the bottom 2 dock connector screws in your iPhone 4. Iphone 4s Dock Connector Replacement
It is the only cross-head screw in your device. It was already damaged. And, (2) I did NOT remove the logic board. http://unmovie.net/iphone-4/iphone-4-not-working-right.html At first it felt like barely anything was happening, but within a few tries the adhesive gave away easily and the battery came right out.
One comment err 2 of the grounding pins broke in the process of reinstallation.. Iphone 4 Dock Connector Problems Use your pry tool to hold it out of the way when removing the dock connector assembly from your iPhone 4. As soon as I would let go, I would get "This accessory may not be supported".
the adhesive on the battery tends to be under the edge of the battery nearest the center of the phone. not necessary! (and it's not mentioned in the video... Phone works fine but what did I do wrong? Dock Connector Iphone Take note that there is a small rubber piece that sits at the top of the logic board.
jhow - 04/12/2014 On an early iPhone 4 I found that the #000 Phillips bit included in the 54 Bit Driver Kit didn't actually fit the screws. robshopping - 09/08/2013 Reply Non problem with reassembly - just took patience - my is that the phone now does not want to charge the battery. Use extreme care and caution when performing a repair on any device. this contact form Paul L Daniels - 08/22/2013 Reply These instructions don't mention putting the 2.5mm screw back in.
I fix(ed) it! The 3 cables further to the right will need to be disconnected as well. Don't use anything flavoured or anything that it likely to have anything other than alcohol and water in it! crimney - 10/02/2013 Reply In Step 5 be EXTRA careful with the battery connector as the socket can come off extremely easy.
Email relay and personal privacy Has a movie ever referred to a later movie? This is the reason why their is simpler guide: iPhone 4 Battery disconnection to be used when there is no necessity for removing the battery. Answered! It's probably in errno.h and strerror.h depending on how far they have gotten from their BSD roots (just add something like ELOWPWR and "This accessory has insufficient power for charging." respectively).
It typically rips or bends the battery. Yes No Voted Undo Score 0 Cancel Comments: First step I would try is to simply just clean the charging port with Isopropyll Alcohol using toothbrush and lint free cloth. Geoff Wall - 02/05/2013 Reply The steps and 12-19 are not necessary for replacing the dock connector on an iPhone 4! The iPhone 5, which features a change to the anatomy of the home button, may solve this problem, but previous iPhone models are still susceptible to this common phenomenon.If you're still