Home > Iphone 4 > Iphone 4s Wifi Not Working After Screen Replacement

Iphone 4s Wifi Not Working After Screen Replacement

Contents

Advice, find a decent philips heard screwdriver for the internal screws like the two found on the battery connector. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Casltech - 11/10/2015 Reply Add a comment Add Comment 1024 Step 14 Edit Use the edge of a plastic opening tool to pry the cable cover tabs out of their slots I managed to get it back in place and reassemble the phone. http://unmovie.net/iphone-4/iphone-4-light-sensor-not-working-after-screen-replacement.html

I have disassembled the phone at least twice and cleaned the screw and connecting metal parts but still experiencing No service or weak 3G signals (one or two bars).... share Share on Twitter Share on Facebook Email Link Like + Quote Reply chomby1991, Feb 22, 2012 chomby1991 macrumors member Joined: Jul 3, 2008 Location: Australia ->queensland ->Rockhampton #16 Nut about Answer this question I have this problem too Subscribed to new answers Is this a good question? The connections to the housing are the following (I included the Steps where you'll see the parts I talk about, refer to this iFixit guide) : - the contact clip (Step https://www.ifixit.com/Answers/View/50484/Wifi+very+weak+after+display+replacement

Iphone 4s Wifi Antenna Fix

Also do not exclude the possibility of a software issue, there are lot of people that swear their WI-Fi connectivity is quite poor since they updated to 4.3.3. 08/01/2011 by Chavdar What I did was I took out the battery, the tin plate above the cables, and lifted the dock connector. You have to be careful not to turn it too much though because this hooked piece is right beside a ribbon that could be damaged. Connected the new battery and aligned the pressure contact screw hole.

Sign in 739 92 Don't like this video? Going through that terrible night myself! Paul - 11/30/2014 Reply During reassembly, I noticed that the data display cable is rather stiff. Iphone 4 Wifi Signal Weak Solution Once I had the back off I loosened all the screws then turned it upside down and shook the crap out of it.

kct16k - 03/15/2014 I just ripped off the power cable ... Hope this helps.Click to expand... It took me about 5 min to understand how it fit! Once I had the back off I loosened all the screws then turned it upside down and shook the crap out of it.

My screws are a pain to get out and if there is a better way of doing this then I'd like to try. Iphone 4 Wifi Antenna Jumper andries - 10/16/2013 Reply This is normal ... How am I supposed to find my screws in that? I've tested it on my working iPhone and WiFi is working fine with or without that wire connected to the logic board.

Wifi Not Working After Screen Replacement Iphone 6

I bumped the table and nothing moved.

Cancel Zlatko Rep: 1 Posted: 09/23/2013 Options Permalink History I have the same problem with my iPhone 4s, poor wifi after screen replacement. Iphone 4s Wifi Antenna Fix rippergirl - 09/12/2013 Reply How can you not remove the battery in a battery replacement fix? Iphone 4 Wifi Antenna Fix Was this answer helpful?

So I ordered a replacement battery about a week ago, and just installed it yesterday. his comment is here For anyone having wifi/GPS issues that has taken apart their phone and thought it might not be a big deal if I don't replace the screw or something doesn't look right, iPhoneCarmine 48,102 views 49:17 Fix Wi-Fi iPhone 4S (Greyed out) - Duration: 3:07. It was very delicate and time consuming operation. My Iphone 6 Wifi Range Is Weak

If the video is no good to you dont leave hate comments just keep searching for what you need .I hope this fix works for you and if it does please The hook is almost right below the socket. Up next iPhone 4S wifi connector problem - Duration: 3:41. http://unmovie.net/iphone-4/iphone-4-new-screen-wifi-not-working.html Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

Sign in to make your opinion count. Weak Wifi Signal Iphone 4 This prevents you from greasing up contacts. 5) Have e.g. Also, some guy from a repair shop suggested here or in another topic that replacing the antenna cable that runs along the loudspeaker enclosure has solved many of their cases of

I removed it from the logic board because the warning was after the instructions.

CyberDoc LLC 107,196 views 21:10 iPhone 4 4S Poor Cellular Signal Fix - Duration: 4:40. Thomas The Train - 11/28/2014 Reply I pried one end of the back off only to find 2 funny little screws holding the other end on so I took my Dremel, A 4S i have here has the left hole bigger and one of the screws didn't want to go into the right hole when it went nicely into the left one. Iphone 4 Wifi Range Problem I put that metal plate UNDER the Antenna while it was loosely fitted - then tightened the screw.- I went from 2 to 3 bars immediately.

This prevents screws from rolling around and you will clearly see anything falling out. 4) If you have them, use tight surgical (latex) gloves. To fix this you will need to synchronize the date and time back to what it is currently. Kevin Keenan - 08/10/2012 Reply While the text refers to the pressure contact, the pictures do not show it clearly. navigate here As noted, the metal lip below the (red) 2.7mm screw and to the right of the (green) 1.2mm screw goes between the ribbon cable and the main logic board.

Part of the metal housing is used for the reception. In Step 8 I think the colors of the screws are inverted. Thanks for the solution!! Has anyone tried with a 000 and does it work better?

Loading... Working... Brian - 04/28/2015 Reply this help me a lot, i just don't know how to fix it(bought it from http://www.laimarket.com/red-replacement...) Dean - 05/24/2015 Reply The phillips head screwdriver provided in the How am I supposed to find my screws in that?

Is the kit supposed to come with both the 1.7 and 1.5mm Philips screwdrivers? Leon Stacey 112,486 views 3:05 Wifi antenna Repair - iPhone 4 How to Tutorial - Duration: 2:58. So I had to figure it out by the photos. Rating is available when the video has been rented.

DMcG - 01/25/2014 Reply I found it easier to start by pulling the plastic lip to loosen the battery, then, if needed, use the plastic tool to pry from the side. Shut it off and when it rebooted it seemed to work. cdays01 - 12/28/2013 Reply step 13 - “One 1.3 mm Phillips screw” step -22 “Notice the small rubber bumper under the screen & digitizer cables (which are detached at top above This step needs to be rewritten imo, the deal here is that there is an actual 'socket' looking deal underneath here that you need to lift up.

Well there is a tiny metal fitting that fits around the screw when you thread it in.