Home > Not Working > Iphone 4 Ear Speaker Not Working Problem

Iphone 4 Ear Speaker Not Working Problem

Contents

At first I was afraid of breaking it, but after reading up on the subject I've learned that it is okay if the battery gets a little deformed. Now what. Marv - 02/07/2015 Reply The replacement panel I got had two sheets of protective plastic on the inside and one on the outside. Social Apples - 07/09/2010 Reply you potentially messed up the ribbon cable from the battery to the adapter. Source

Huawei's P9 passes 9 million in sales Close   Discuss: No iPhone audio (speaker or earpiece not... If you are still under warranty, after they do the diagnostics or look at it, they will swap it out. iPhoneRepairMia 70,079 views 4:52 Iphone 4 top speaker replacement - Duration: 6:19. Thanks for this pic! https://discussions.apple.com/thread/3380936?start=60&tstart=0

Iphone Ear Speaker Very Quiet

It typically rips or bends the battery. It may sound silly but i can attest that this method works!! Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? I've tried plugging and unplugging the headphones, and I also did a complete restore.

Was this answer helpful? richard - 01/03/2015 Reply Just went through the replacement and the battery "plug" (step 5) on my replacement battery was slightly misaligned relative to the metal plate used to screw it I've done iPod screen replacements, battery replacements, this is by far much more difficult and intricate. Iphone Earpiece Not Working But Speaker Does then turned off network settings in settings, then turned them back on, and I got 3 bars.

How can I work on my phone if its covered in dirt? Try cleaning it with a cotton bud (preferably with a tiny bit of rubbing alcohol or if you haven't got that, wet the bud so it is damp - do not That contact point must be in a plane above every other surface inside the device when you replace the battery connector, because it makes a ground contact with the metallic inner I have had dozens handed in to me with punctures and two that actually started smoking due to people trying to prise the battery out.

I tried The Suck & got some relief, but Aram's suggestion got my phone back to full functionality. Iphone Ear Speaker Not Working Water This step needs to be rewritten imo, the deal here is that there is an actual 'socket' looking deal underneath here that you need to lift up. Give the author +30 points! I just pried the battery connector up (gently) with a spudger and left the pressure contact in place.

Iphone 6 Ear Speaker Not Working

NOW IT WORKS! a fantastic read any suggestions? Iphone Ear Speaker Very Quiet The screwdriver won't even fit into the screw, and I can't get it out (I have no idea how they got it in in the first place). Iphone 5 Ear Speaker Not Working It goes black side up with the pressure contact touching the back of the phone when the cover is in place.

mhejjas - 11/19/2011 Reply Add a comment Add Comment 1024 Step 8 Edit Remove the following two screws: One 1.2 mm Phillips One 1.6 mm Phillips Remove the thin steel dock this contact form I think the guide should be edited to note that battery removal is not necessary. This is to ensure there is no mix-up, and avoid rendering the LCD and digitizer useless. Try to rake it out with a paperclip. Iphone 4 Ear Speaker Not Working Solution

You're Finished! Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. bfbogaert - 11/17/2012 Reply There is a metal bracket that secures the connector, that will be removed before the conector is unfasten poseido - 06/03/2013 Reply When I used a plastic http://unmovie.net/not-working/keyboard-problem-not-working.html bluezzer - 10/29/2013 I bent the wire of the silent button on right top of the battery.

Tried sucking as hard as physically possible, tried blowing, tried the wet toothbrush followed by a big shop vac...no luck. Iphone 6s Earpiece Not Working I did what no one should do. The average guy's gonna screw up his phone big time if he follows these instructions and nobody warns him about all the dirt that's gonna end up in his phone.

Unclip the top logic board cables & remove the rear-facing camera Using your spudger or pry tool carefully disconnect all the cables at the top of the logic board.

On some units, they use so much glue that it's virtually impossible to take the battery. powers74 - 09/19/2014 Reply It's probably the nut for the yellow screw of step 13. Was this answer helpful? Iphone Ear Speaker Not Working After Screen Replacement This helped re-assembly griffn - 09/10/2015 Reply Also remove 4 screws holding metal cover plate adjacent to camera lens, remove plate to expose camera plug.

Colorblend - 11/21/2014 Reply I dismantled the phone again and concluded that the digitizer cable was kind of loose (don't know if that affected anything, but i put it down firmly It may also simply be that you need to change the ear speaker in the phone. Yes No Voted Undo Score 0 Cancel Comments: Ok so my outter speaker works perfectly fine, but the ear piece speaker doesn't work properly, it fries and make baffling sounds, when Check This Out i have now a working iPhone back after display crash and glass brake!

Look at the other guides for the 4S they show the 4 screws and how to lift the shield out, take out the camera etc. It's only obvious after a really close look and if one has a lot to do like I did, it's a long time before one comes back to this step so Make sure that it is properly seated before reassembly. 3 comments Im pretty sure that when you reinsert the cam the grounding clip has go to between metal sticker and the That's the primary reason for abnormal Wi-Fi performance after the reassembly.

I see others have had this problem. You wouldn't by chance work in a weld shop or other area with tiny metal airborne particles? Thanks again you wonderful genius! :D Was this answer helpful? If you don't get this right, the 2.7mm screw is difficult and, worse, there's a risk the edge of the lip will tear the ribbon cable.

I had to use the included pry tool to get the back off. Phone works fine without it, though. It will have full reception (5 pins) for about 10 seconds, then drop to 1 pin for a couple seconds, then go into "searching" mode. share Share on Twitter Share on Facebook Email Link Like + Quote Reply Zzsr81, Jan 13, 2012 Zzsr81 macrumors newbie Joined: Jan 13, 2012 #12 I'm having the exact same problem-

The hook is almost right below the socket.